A chamfer is a surface produced by cutting away an arris. From Wordnik.com. [Handwork in Wood] Reference
The last one uses one called chamfer along path. From Wordnik.com. [bit-tech.net Feed] Reference
Here, the chamfer is a definate nuisance. From Wordnik.com. [Epinions Recent Content for Home] Reference
Slightly chamfer the steps at the cross-grain end. From Wordnik.com. [Chapter 9] Reference
Slightly chamfer the risers at the cross-grain end. From Wordnik.com. [Chapter 9] Reference
Mine had a chamfer, a fillet, and a few odd channels. From Wordnik.com. [Colin Summers: Learning to Draw] Reference
The lower part is a plain, hollowed chamfer moulding. From Wordnik.com. [Bell's Cathedrals: Chichester (1901) A Short History & Description Of Its Fabric With An Account Of The Diocese And See] Reference
Lay board flat and chamfer at tongue and groove sides. From Wordnik.com. [Chapter 3] Reference
Grind the narrow surfaces manually, chamfer the edges. From Wordnik.com. [Chapter 6] Reference
Might also chamfer the edges just a little with a file. From Wordnik.com. [well i started building my new muzzleloader, and i ran into a problem, i cant seem to get the barrel tenon into the dovetail in] Reference
BTW, I always trim for length and chamfer for every load. From Wordnik.com. [How Many Groups is Enough?] Reference
Smooth inner angle faces with file, chamfer all edges. cutting oil. From Wordnik.com. [Chapter 6] Reference
Without chamfer; best plan for view of both square and hexagon heads 123. From Wordnik.com. [Mechanical Drawing Self-Taught] Reference
A new degree of difficulty is added by filing a chamfer on round material. From Wordnik.com. [1. Objectives and contents of practical vocational training in the working technique of Filing] Reference
Figure 39 Filing of a chamfer on small workpieces by means of an angle vice. From Wordnik.com. [6. Handling of the files] Reference
The amount of chamfer should be approximately equal to the pitch (chamfer = t). From Wordnik.com. [4. Straight knurling of small widths on simple cylindrical parts] Reference
Have participants return to their stations and forge, grind and chamfer the cold chisels. From Wordnik.com. [Chapter 8] Reference
The chamfer shall have an inclination of approximately 45° and a width of at least 0.5 mm. From Wordnik.com. [8. Technological process of cutting external threads] Reference
Grinding of a chamfer of 4 mm at both sides of the handle - horizontal or vertical position!. From Wordnik.com. [Chapter 4] Reference
Either chamfer or round the upper ends as desired. From Wordnik.com. [Mission Furniture How to Make It, Part 2] Reference
First - the chamfer is made with countersink tool. From Wordnik.com. [All Discussion Groups: Message List - root]
The way chamfer computes is quite similar to fillet. From Wordnik.com. [All Discussion Groups: Message List - root]
I've never seen a machined chamfer on anyone else's rail. From Wordnik.com. [Defense Review] Reference
In this case the chamfer will have uniform width along the edge. From Wordnik.com. [All Discussion Groups: Message List - root]
Once the boundaries are defined, the chamfer face can be obtained. From Wordnik.com. [All Discussion Groups: Message List - root]
You can also already add a leader from a chamfer, so why not a radius?. From Wordnik.com. [All Discussion Groups: Message List - root] Reference
An application of oxygen cutting in which a chamfer or groove is formed. From Wordnik.com. [MyLinkVault Newest Links] Reference
Create a workpoint (C) by selecting the chamfer boundary edge (bottom) and. From Wordnik.com. [All Discussion Groups: Message List - root]
Using this tool, exact chamfer diameters can be set without trial and error. From Wordnik.com. [PRWeb - Daily News Feed] Reference
Create a 3D Sketch - > include geometry - > pick the chamfer edge - > finish. From Wordnik.com. [All Discussion Groups: Message List - root]
In the attached file the edge chamfer delivers different reading when measured. From Wordnik.com. [All Discussion Groups: Message List - root]
Cut to the length desired and chamfer both ends inside and out side (de-burr it). From Wordnik.com. [SurvivalBlog.com] Reference
Create a workpoint (B) by selecting the chamfer boundary edge (top) and YZ plane. From Wordnik.com. [All Discussion Groups: Message List - root]
Create a workpoint (C) by selecting the chamfer boundary edge (bottom) and YZ plane. From Wordnik.com. [All Discussion Groups: Message List - root]
However if I try the new interactive mode only the first chamfer/fillet will succeed. From Wordnik.com. [All Discussion Groups: Message List - root]
To create the chamfer: draw the shape of the chamfer using a polyline in model space. From Wordnik.com. [All Discussion Groups: Message List - root] Reference
I was asking why two opposite edges of the same hole show different chamfer geometry?. From Wordnik.com. [All Discussion Groups: Message List - root]
As for the way the chamfer is represented in such models - there can be two approaches. From Wordnik.com. [All Discussion Groups: Message List - root]
The chamfer one will do fillets too, but you need to play with the #s a bit to get it right. From Wordnik.com. [bit-tech.net Feed] Reference
LearnThatWord and the Open Dictionary of English are programs by LearnThat Foundation, a 501(c)3 nonprofit.
Questions? Feedback? We want to hear from you!
Email us
or click here for instant support.
Copyright © 2005 and after - LearnThat Foundation. Patents pending.