Standard carburetors use similar venturi profiles.    From Wordnik.com.  [6. The Gas Otto Engine] Reference

A venturi mixer is shown further below in Fig. 6.2.    From Wordnik.com.  [5. The Gas Diesel Engine] Reference

A venturi mixer in its details is given in Appendix IV.    From Wordnik.com.  [6. The Gas Otto Engine] Reference

At the end of each tube there is what we call a 'venturi tube.'.    From Wordnik.com.  [Around the World in Ten Days] Reference

For the design parameters of a venturi mixer refer to Chapter 6.    From Wordnik.com.  [5. The Gas Diesel Engine] Reference

The function is somewhat similar to the function of a venturi jet.    From Wordnik.com.  [5. The Gas Diesel Engine] Reference

The calculations need to consider the actual size of the given venturi.    From Wordnik.com.  [6. The Gas Otto Engine] Reference

Av cross-sectional area of venturi contractor ( "bottleneck") m², mm².    From Wordnik.com.  [Chapter 15] Reference

Otto: fixed setting of gas and air or throttle in the case of a venturi.    From Wordnik.com.  [Chapter 17] Reference

In any position it shall not interfere with the flow through the venturi ring.    From Wordnik.com.  [6. The Gas Otto Engine] Reference

Otto: adjustment of gas/air valves or throttle (venturi) whenever load changes.    From Wordnik.com.  [Chapter 17] Reference

Fed by compressed air line or tank, compressed air flows through a venturi Jet.    From Wordnik.com.  [7.1 Pneumatic jack hammer, drilling stand, jackleg] Reference

The venturi gas mixer can thus always be adjusted to the actual fuel gas conditions.    From Wordnik.com.  [6. The Gas Otto Engine] Reference

The venturi shall therefore be evenly shaped following the example given in Fig. 6.2.    From Wordnik.com.  [6. The Gas Otto Engine] Reference

Biogas is introduced through a nozzle pointing into the core of the venturi bottleneck.    From Wordnik.com.  [10. Overview of Commercially Available Systems] Reference

The cross-sectional dimension of the venturi mixer should be equal to that of the manifold.    From Wordnik.com.  [6. The Gas Otto Engine] Reference

An extra O-ring in a groove will suffice to tighten the venturi ring against the tube body.    From Wordnik.com.  [6. The Gas Otto Engine] Reference

Should the venturi mixer used have a throttle, it should be kept fully open at any condition.    From Wordnik.com.  [5. The Gas Diesel Engine] Reference

Air for combustion is drawn into the burner by the venturi effect of the pressurized fuel gas.    From Wordnik.com.  [2. Kilns] Reference

The venturi ring requires careful machining on a lathe machine and an extremely smooth surface.    From Wordnik.com.  [6. The Gas Otto Engine] Reference

With a ratio between the manifold inlet diameter and the venturi jet diameter of di/dv = 1.5.    From Wordnik.com.  [5. The Gas Diesel Engine] Reference

LPG, natural gas: mixing valve or venturi, with pressure reduction valve (50 mbar) before gas inlet.    From Wordnik.com.  [6. The Gas Otto Engine] Reference

A smaller bottleneck diameter increases the venturi velocity while a larger one decreases it respectively.    From Wordnik.com.  [6. The Gas Otto Engine] Reference

Take me for a ride in your 3.2 liter Ferrari with torsion bar suspension and those ported venturi carburetors!.    From Wordnik.com.  [Car-Car] Reference

The following procedure shall give a general representation of the dimensioning of a (self-made) venturi mixer.    From Wordnik.com.  [6. The Gas Otto Engine] Reference

The hole will have to meet the venturi at its bottleneck and be big enough to allow the required biogas to join the airstream.    From Wordnik.com.  [6. The Gas Otto Engine] Reference

This is achieved by adequate design of the mixing device, whether a venturi mixer or a suction-pressure controlled mixing valve.    From Wordnik.com.  [6. The Gas Otto Engine] Reference

Determine the mean intake velocity c; (in m/s) of the venturi mixer using the channel's cross-sectional area Ai (in m²), see Equ.    From Wordnik.com.  [6. The Gas Otto Engine] Reference

This means that its downstream distance from the venturi ring end needs to be at least 0.5 times the main channel's (inlet) diameter di.    From Wordnik.com.  [6. The Gas Otto Engine] Reference

Four venturi devices have been installed in one compartment of the underground reservoir to increase aeration in the circulation pattern.    From Wordnik.com.  [Chapter 13] Reference

The venturi ring is held in position by a setscrew fitting into a small hole in the center of the circumferential fuel gas supply channel.    From Wordnik.com.  [6. The Gas Otto Engine] Reference

The volumetric intake of the engine Vi can also be used to determine the velocity cv: when the venturi bottleneck area Av is already known.    From Wordnik.com.  [6. The Gas Otto Engine] Reference

Street cars are hit or miss on how well a venturi in the exhaust will work, from my research.    From Wordnik.com.  [NASIOC] Reference