The workpiece is shortly quenched after having been hardened so that only outer layer is cold.    From Wordnik.com.  [6. Tempering] Reference

Reduction of quality, rework or unusefulness of the workpiece are the consequence.    From Wordnik.com.  [3. Preparing face and parallel milling] Reference

Infeed by tool rest and surfacing of the workpiece.    From Wordnik.com.  [5. Setting-up and operating the regular engine lathe] Reference

In case of ripping the workpiece must be fixed rigidly.    From Wordnik.com.  [3. Preparation for Mortising and Ripping] Reference

Figure 7 Clamping the workpiece on a carpenter’s bench.    From Wordnik.com.  [3. Preparation for Mortising and Ripping] Reference

When planing a workpiece to the required thickness, then.    From Wordnik.com.  [4. Planing of Wide Faces] Reference

Why must a clamp always lie horizontally on the workpiece?.    From Wordnik.com.  [4. Preparation for working with shaping machines] Reference

Holding time = 20 minutes plus half of workpiece thickness.    From Wordnik.com.  [1. Objectives and Contents of the Vocational Training in the Working Techniques “Annealing, Hardening, Tempering”] Reference

Starting the cut at the workpiece for dimensional inspection.    From Wordnik.com.  [5. Setting-up and operating the regular engine lathe] Reference

A workpiece has a diameter of 50.8 mm and shall be reduced to.    From Wordnik.com.  [5. Setting-up and operating the regular engine lathe] Reference

The true-running accuracy of the workpiece must be ensured.    From Wordnik.com.  [4. Reaming with solid reamer] Reference

“A” (according to the appearance of the broken workpiece) 19.    From Wordnik.com.  [1. Objectives and Contents of the Vocational Training in the Working Techniques “Annealing, Hardening, Tempering”] Reference

Which influence has the workpiece thickness on the bending radius?.    From Wordnik.com.  [3. Processes within in the Material] Reference

Entering the cut at the workpiece with the help of the hand feed.    From Wordnik.com.  [5. Setting-up and operating the regular engine lathe] Reference

The chucked workpiece begins turning as the machine is switched on.    From Wordnik.com.  [5. Mode of Operation of a Wood Turning Lathe] Reference

Before working them, mark out the respective areas of the workpiece.    From Wordnik.com.  [3. Preparation for Mortising and Ripping] Reference

Place the gauge against the workpiece and hold it against the light!.    From Wordnik.com.  [3. Testing Tools] Reference

The light gap between the gauge and workpiece must be evenly narrow!.    From Wordnik.com.  [3. Testing Tools] Reference

Given: workpiece length l = 180 mm approach and overrun la + lo = 30 mm.    From Wordnik.com.  [4. Preparation for working with shaping machines] Reference

Approaching the tool carrier with the lathe tool towards the workpiece.    From Wordnik.com.  [5. Setting-up and operating the regular engine lathe] Reference

Which effect has the use of a coarse quenching medium onto the workpiece?.    From Wordnik.com.  [1. Objectives and Contents of the Vocational Training in the Working Techniques “Annealing, Hardening, Tempering”] Reference

“A” (elimination of stresses existing in the prefabricated workpiece) 14.    From Wordnik.com.  [1. Objectives and Contents of the Vocational Training in the Working Techniques “Annealing, Hardening, Tempering”] Reference

Before the workpiece is clamped the position of the machine vice must be checked.    From Wordnik.com.  [4. Preparation for working with shaping machines] Reference

Metal chips on the workpiece faces or burrs on the already processed faces lead to.    From Wordnik.com.  [3. Preparation for milling offset faces] Reference

Which influence has the bending radius on the formation of cracks in the workpiece?.    From Wordnik.com.  [3. Processes within in the Material] Reference

The scraper is moved over the workpiece by the pushing or puling power of the hand.    From Wordnik.com.  [5. Operation of scraping] Reference

The most frequently employed workpiece clamping means for milling offset faces are.    From Wordnik.com.  [3. Preparation for milling offset faces] Reference

Existing defects should be made visible by a paint coat on a workpiece having cracks.    From Wordnik.com.  [1. Objectives and Contents of the Vocational Training in the Working Techniques “Annealing, Hardening, Tempering”] Reference

Cutting in (a small groove in the workpiece) at the rotating metal slitting saw blade.    From Wordnik.com.  [4. Cutting by milling] Reference

Beginning the cut at the area of the cylindrical surface of the workpiece by hand feed.    From Wordnik.com.  [5. Setting-up and operating the regular engine lathe] Reference

The cutting depth at cutting by milling corresponds to the width or height or the workpiece.    From Wordnik.com.  [4. Cutting by milling] Reference

The more the workpiece is being remodelled, the bigger are the stresses inside the material.    From Wordnik.com.  [3. Processes within in the Material] Reference

How can workpiece and workpiece clamping means with greater accuracy requirements be aligned?.    From Wordnik.com.  [3. Preparation for milling offset faces] Reference

Acting bending forces cause stresses in the material affecting a remodelling of the workpiece.    From Wordnik.com.  [3. Processes within in the Material] Reference

When clamping workpiece directly to the machine table the following preconditions must be met.    From Wordnik.com.  [3. Preparation for milling offset faces] Reference

“A” (heating to hardening temperature, holding and sudden cooling down of the workpiece) 24.    From Wordnik.com.  [1. Objectives and Contents of the Vocational Training in the Working Techniques “Annealing, Hardening, Tempering”] Reference

The neutral axis length is needed to calculate the stretched length of the workpiece to be bent.    From Wordnik.com.  [3. Processes within in the Material] Reference

"A" (Irregularly shaped abrasive grains will shave fine segmental chips from the workpiece.) 10.    From Wordnik.com.  [3. Recommendations for practical vocational training in the working technique of ''Grinding of Simple Tools''] Reference

Figure 14 Stresses in the bent workpiece 1 tensile stresses, 2 neutral axis, 3 compressive stresses.    From Wordnik.com.  [3. Processes within in the Material] Reference